libre-testing: remove outdated u-boot packages

All these u-boot pakcages were consolidated in SOC specific packages
instead of board specific pakcages in libre.

In addition the libre packages are more recent and in sync with the
Parabola armv7h installation manual.

Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>

6 files changed, 0 insertions, 482 deletions

diff --git a/libre-testing/uboot4extlinux-omap3_beagle/0001-parabola-arm-modifications.patch b/libre-testing/uboot4extlinux-omap3_beagle/0001-parabola-arm-modifications.patch
deleted file mode 100644
index c99cd89b8..000000000
--- a/libre-testing/uboot4extlinux-omap3_beagle/0001-parabola-arm-modifications.patch
+++ /dev/null
@@ -1,312 +0,0 @@
-diff -Nur u-boot-2016.01.orig/board/ti/beagle/beagle.c u-boot-2016.01/board/ti/beagle/beagle.c
---- u-boot-2016.01.orig/board/ti/beagle/beagle.c	2016-01-12 11:06:54.000000000 -0300
-+++ u-boot-2016.01/board/ti/beagle/beagle.c	2016-02-24 19:45:05.779336247 -0300
-@@ -56,6 +56,7 @@
- #define BBTOYS_WIFI			0x01000B00
- #define BBTOYS_VGA			0x02000B00
- #define BBTOYS_LCD			0x03000B00
-+#define BBTOYS_ULCD			0x04000B00
- #define BCT_BRETTL3			0x01000F00
- #define BCT_BRETTL4			0x02000F00
- #define LSR_COM6L_ADPT			0x01001300
-@@ -211,25 +212,25 @@
-  *		bus 1 for the availability of an AT24C01B serial EEPROM.
-  *		returns the device_vendor field from the EEPROM
-  */
--static unsigned int get_expansion_id(void)
-+static unsigned int get_expansion_id(int eeprom_address)
- {
- 	i2c_set_bus_num(EXPANSION_EEPROM_I2C_BUS);
- 
- 	/* return BEAGLE_NO_EEPROM if eeprom doesn't respond */
--	if (i2c_probe(EXPANSION_EEPROM_I2C_ADDRESS) == 1) {
-+	if (i2c_probe(eeprom_address) == 1) {
- 		i2c_set_bus_num(TWL4030_I2C_BUS);
- 		return BEAGLE_NO_EEPROM;
- 	}
- 
- 	/* read configuration data */
--	i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 1, (u8 *)&expansion_config,
-+	i2c_read(eeprom_address, 0, 1, (u8 *)&expansion_config,
- 		 sizeof(expansion_config));
- 
- 	/* retry reading configuration data with 16bit addressing */
- 	if ((expansion_config.device_vendor == 0xFFFFFF00) ||
- 	    (expansion_config.device_vendor == 0xFFFFFFFF)) {
- 		printf("EEPROM is blank or 8bit addressing failed: retrying with 16bit:\n");
--		i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 2, (u8 *)&expansion_config,
-+		i2c_read(eeprom_address, 0, 2, (u8 *)&expansion_config,
- 			 sizeof(expansion_config));
- 	}
- 
-@@ -341,15 +342,18 @@
- 	case REVISION_AXBX:
- 		printf("Beagle Rev Ax/Bx\n");
- 		setenv("beaglerev", "AxBx");
-+		setenv("musb", "musb_hdrc.fifo_mode=5");
- 		break;
- 	case REVISION_CX:
- 		printf("Beagle Rev C1/C2/C3\n");
- 		setenv("beaglerev", "Cx");
-+		setenv("musb", "musb_hdrc.fifo_mode=5");
- 		MUX_BEAGLE_C();
- 		break;
- 	case REVISION_C4:
- 		printf("Beagle Rev C4\n");
- 		setenv("beaglerev", "C4");
-+		setenv("musb", "musb_hdrc.fifo_mode=5");
- 		MUX_BEAGLE_C();
- 		/* Set VAUX2 to 1.8V for EHCI PHY */
- 		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
-@@ -390,7 +394,7 @@
- 		generate_fake_mac = true;
- 	}
- 
--	switch (get_expansion_id()) {
-+	switch (get_expansion_id(EXPANSION_EEPROM_I2C_ADDRESS)) {
- 	case TINCANTOOLS_ZIPPY:
- 		printf("Recognized Tincantools Zippy board (rev %d %s)\n",
- 			expansion_config.revision,
-@@ -471,6 +475,30 @@
- 	}
- 
- 	if (expansion_config.content == 1)
-+		setenv(expansion_config.env_var, expansion_config.env_setting);
-+
-+	/* Scan 0x51 as well for loop-thru boards */
-+	switch (get_expansion_id(EXPANSION_EEPROM_I2C_ADDRESS + 1)) {
-+	case BBTOYS_ULCD:
-+		printf("Recognized BeagleBoardToys uLCD-lite board\n");
-+		setenv("buddy2", "bbtoys-ulcd");
-+		setenv("defaultdisplay", "dvi");
-+		setenv("dvimode", "800x480MR-16@60");
-+		setenv("lcd1", "i2c mw 40 00 00; i2c mw 40 04 80; i2c mw 40 0d 05");
-+		setenv("lcdcmd", "i2c dev 1 ; run lcd1; i2c dev 0");
-+		setenv("kmsmode", "video=DVI-D-1:800x480");
-+		break;
-+	case BEAGLE_NO_EEPROM:
-+		printf("No EEPROM on expansion board\n");
-+		setenv("buddy2", "none");
-+		break;
-+	default:
-+		printf("Unrecognized expansion board: %x\n",
-+			expansion_config.device_vendor);
-+		setenv("buddy2", "unknown");
-+	}
-+
-+	if (expansion_config.content == 1)
- 		setenv(expansion_config.env_var, expansion_config.env_setting);
- 
- 	twl4030_power_init();
-diff -Nur u-boot-2016.01.orig/include/configs/omap3_beagle.h u-boot-2016.01/include/configs/omap3_beagle.h
---- u-boot-2016.01.orig/include/configs/omap3_beagle.h	2016-01-12 11:06:54.000000000 -0300
-+++ u-boot-2016.01/include/configs/omap3_beagle.h	2016-02-24 19:50:25.959802093 -0300
-@@ -91,6 +91,12 @@
- #define CONFIG_USB_ETHER_MCS7830
- #define CONFIG_USB_ETHER_SMSC95XX
- 
-+/* Parabola GNU/Linux-libre extras */
-+#define CONFIG_IDENT_STRING " Parabola GNU/Linux-libre"
-+#define CONFIG_SUPPORT_RAW_INITRD
-+#define CONFIG_CMD_PART
-+#define CONFIG_PARTITION_UUIDS
-+
- /* GPIO banks */
- #define CONFIG_OMAP3_GPIO_5		/* GPIO128..159 is in GPIO bank 5 */
- #define CONFIG_OMAP3_GPIO_6		/* GPIO160..191 is in GPIO bank 6 */
-@@ -124,51 +130,71 @@
- #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
- 							/* devices */
- 
-+/* Enable Extlinux boot support */
-+#define CONFIG_CMD_PXE
-+#define CONFIG_MENU
-+#define BOOT_TARGET_DEVICES(func)
-+#include <config_distro_bootcmd.h>
-+
- #define CONFIG_EXTRA_ENV_SETTINGS \
--	"loadaddr=0x80200000\0" \
--	"rdaddr=0x81000000\0" \
-+	BOOTENV \
-+	"loadaddr=0x82000000\0" \
-+	"rdaddr=0x88080000\0" \
- 	"fdt_high=0xffffffff\0" \
--	"fdtaddr=0x80f80000\0" \
--	"usbtty=cdc_acm\0" \
--	"bootfile=uImage\0" \
--	"ramdisk=ramdisk.gz\0" \
--	"bootdir=/boot\0" \
--	"bootpart=0:2\0" \
-+	"fdtaddr=0x88000000\0" \
- 	"console=ttyO2,115200n8\0" \
--	"mpurate=auto\0" \
--	"buddy=none\0" \
--	"optargs=\0" \
--	"camera=none\0" \
--	"vram=12M\0" \
--	"dvimode=640x480MR-16@60\0" \
--	"defaultdisplay=dvi\0" \
-+	"fdtfile=undefined\0" \
-+	"bootpart=0:1\0" \
-+	"bootdir=\0" \
-+	"fdtdir=/dtbs\0" \
-+	"bootfile=zImage\0" \
-+	"rdfile=initramfs-linux.img\0" \
- 	"mmcdev=0\0" \
--	"mmcroot=/dev/mmcblk0p2 rw\0" \
--	"mmcrootfstype=ext3 rootwait\0" \
--	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
--	"nandrootfstype=ubifs\0" \
--	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
--	"ramrootfstype=ext2\0" \
-+	"optargs=\0" \
- 	"mmcargs=setenv bootargs console=${console} " \
- 		"${optargs} " \
--		"mpurate=${mpurate} " \
--		"buddy=${buddy} "\
--		"camera=${camera} "\
--		"vram=${vram} " \
--		"omapfb.mode=dvi:${dvimode} " \
--		"omapdss.def_disp=${defaultdisplay} " \
--		"root=${mmcroot} " \
--		"rootfstype=${mmcrootfstype}\0" \
--	"nandargs=setenv bootargs console=${console} " \
--		"${optargs} " \
--		"mpurate=${mpurate} " \
--		"buddy=${buddy} "\
--		"camera=${camera} "\
--		"vram=${vram} " \
--		"omapfb.mode=dvi:${dvimode} " \
--		"omapdss.def_disp=${defaultdisplay} " \
--		"root=${nandroot} " \
--		"rootfstype=${nandrootfstype}\0" \
-+		"root=${root} " \
-+		"${musb} " \
-+		"${cmdline}\0" \
-+	"loadimage=load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
-+	"loadrd=load ${devtype} ${bootpart} ${rdaddr} ${bootdir}/${rdfile}\0" \
-+	"loadfdt=echo loading ${fdtdir}/${fdtfile} ...; load ${devtype} ${bootpart} ${fdtaddr} ${fdtdir}/${fdtfile}\0" \
-+	"mmcboot=usb start;" \
-+		"for devtype in mmc usb; do " \
-+			"setenv devnum 0;" \
-+			"while ${devtype} dev ${devnum}; do " \
-+				"echo ${devtype} found on device ${devnum};" \
-+				"setenv bootpart ${devnum}:1;" \
-+				"if test ${devtype} = mmc; then part uuid mmc ${devnum}:2 uuid; else part uuid ${devtype} ${devnum}:1 uuid; fi;" \
-+				"part uuid ${devtype} ${rootpart} uuid;" \
-+				"setenv root PARTUUID=${uuid} rw rootwait;" \
-+				"echo Checking for: ${bootdir}/uEnv.txt ...;" \
-+				"if test -e ${devtype} ${bootpart} ${bootdir}/uEnv.txt; then " \
-+					"load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/uEnv.txt;" \
-+					"env import -t ${loadaddr} ${filesize};" \
-+					"echo Loaded environment from ${bootdir}/uEnv.txt;" \
-+					"echo Checking if uenvcmd is set ...;" \
-+					"if test -n ${uenvcmd}; then " \
-+						"echo Running uenvcmd ...;" \
-+						"run uenvcmd;" \
-+					"fi;" \
-+				"fi;" \
-+				"run scan_dev_for_boot;" \
-+				"if run loadimage; then " \
-+					"run mmcargs;" \
-+					"if run loadfdt; then " \
-+						"if run loadrd; then " \
-+							"bootz ${loadaddr} ${rdaddr}:${filesize} ${fdtaddr};" \
-+						"else " \
-+							"bootz ${loadaddr} - ${fdtaddr};" \
-+						"fi;" \
-+					"fi;" \
-+				"else " \
-+					"echo No kernel found;" \
-+				"fi;" \
-+				"setexpr devnum ${devnum} + 1;" \
-+			"done;" \
-+		"done;\0" \
- 	"findfdt=" \
- 		"if test $beaglerev = AxBx; then " \
- 			"setenv fdtfile omap3-beagle.dtb; fi; " \
-@@ -181,81 +207,11 @@
- 		"if test $beaglerev = xMC; then " \
- 			"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
- 		"if test $fdtfile = undefined; then " \
--			"echo WARNING: Could not determine device tree to use; fi; \0" \
--	"validatefdt=" \
--		"if test $beaglerev = xMAB; then " \
--			"if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
--				"setenv fdtfile omap3-beagle-xm.dtb; " \
--			"fi; " \
--		"fi; \0" \
--	"bootenv=uEnv.txt\0" \
--	"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
--	"importbootenv=echo Importing environment from mmc ...; " \
--		"env import -t -r $loadaddr $filesize\0" \
--	"ramargs=setenv bootargs console=${console} " \
--		"${optargs} " \
--		"mpurate=${mpurate} " \
--		"buddy=${buddy} "\
--		"vram=${vram} " \
--		"omapfb.mode=dvi:${dvimode} " \
--		"omapdss.def_disp=${defaultdisplay} " \
--		"root=${ramroot} " \
--		"rootfstype=${ramrootfstype}\0" \
--	"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
--	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
--	"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
--	"bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
--		"source ${loadaddr}\0" \
--	"loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
--	"mmcboot=echo Booting from mmc ...; " \
--		"run mmcargs; " \
--		"bootm ${loadaddr}\0" \
--	"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
--		"run mmcargs; " \
--		"bootz ${loadaddr} - ${fdtaddr}\0" \
--	"nandboot=echo Booting from nand ...; " \
--		"run nandargs; " \
--		"nand read ${loadaddr} 280000 400000; " \
--		"bootm ${loadaddr}\0" \
--	"ramboot=echo Booting from ramdisk ...; " \
--		"run ramargs; " \
--		"bootm ${loadaddr}\0" \
--	"userbutton=if gpio input 173; then run userbutton_xm; " \
--		"else run userbutton_nonxm; fi;\0" \
--	"userbutton_xm=gpio input 4;\0" \
--	"userbutton_nonxm=gpio input 7;\0"
--/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
-+			"echo WARNING: Could not determine device tree to use; fi; \0"
-+
- #define CONFIG_BOOTCOMMAND \
- 	"run findfdt; " \
--	"mmc dev ${mmcdev}; if mmc rescan; then " \
--		"if run userbutton; then " \
--			"setenv bootenv uEnv.txt;" \
--		"else " \
--			"setenv bootenv user.txt;" \
--		"fi;" \
--		"echo SD/MMC found on device ${mmcdev};" \
--		"if run loadbootenv; then " \
--			"echo Loaded environment from ${bootenv};" \
--			"run importbootenv;" \
--		"fi;" \
--		"if test -n $uenvcmd; then " \
--			"echo Running uenvcmd ...;" \
--			"run uenvcmd;" \
--		"fi;" \
--		"if run loadbootscript; then " \
--			"run bootscript; " \
--		"else " \
--			"if run loadimage; then " \
--				"run mmcboot;" \
--			"fi;" \
--		"fi; " \
--	"fi;" \
--	"run nandboot;" \
--	"setenv bootfile zImage;" \
--	"if run loadimage; then " \
--		"run loadfdt;" \
--		"run mmcbootz; " \
--	"fi; " \
-+	"run mmcboot"
- 
- /*
-  * OMAP3 has 12 GP timers, they can be driven by the system clock
diff --git a/libre-testing/uboot4extlinux-omap3_beagle/0002-kernel-add-support-for-gcc-7.patch b/libre-testing/uboot4extlinux-omap3_beagle/0002-kernel-add-support-for-gcc-7.patch
deleted file mode 100644
index ca59b159a..000000000
--- a/libre-testing/uboot4extlinux-omap3_beagle/0002-kernel-add-support-for-gcc-7.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-diff --git a/include/linux/compiler-gcc7.h b/include/linux/compiler-gcc7.h
-new file mode 100644
-index 0000000..ba064fa
---- /dev/null
-+++ b/include/linux/compiler-gcc7.h
-@@ -0,0 +1,59 @@
-+#ifndef __LINUX_COMPILER_H
-+#error "Please don't include <linux/compiler-gcc7.h> directly, include <linux/compiler.h> instead."
-+#endif
-+
-+#define __used				__attribute__((__used__))
-+#define __must_check			__attribute__((warn_unused_result))
-+#define __compiler_offsetof(a, b)	__builtin_offsetof(a, b)
-+
-+/* Mark functions as cold. gcc will assume any path leading to a call
-+   to them will be unlikely.  This means a lot of manual unlikely()s
-+   are unnecessary now for any paths leading to the usual suspects
-+   like BUG(), printk(), panic() etc. [but let's keep them for now for
-+   older compilers]
-+
-+   gcc also has a __attribute__((__hot__)) to move hot functions into
-+   a special section, but I don't see any sense in this right now in
-+   the kernel context */
-+#define __cold			__attribute__((__cold__))
-+
-+#define __UNIQUE_ID(prefix) __PASTE(__PASTE(__UNIQUE_ID_, prefix), __COUNTER__)
-+
-+#ifndef __CHECKER__
-+# define __compiletime_warning(message) __attribute__((warning(message)))
-+# define __compiletime_error(message) __attribute__((error(message)))
-+#endif /* __CHECKER__ */
-+
-+/*
-+ * Mark a position in code as unreachable.  This can be used to
-+ * suppress control flow warnings after asm blocks that transfer
-+ * control elsewhere.
-+ */
-+#define unreachable() __builtin_unreachable()
-+
-+/* Mark a function definition as prohibited from being cloned. */
-+#define __noclone	__attribute__((__noclone__))
-+
-+/*
-+ * Tell the optimizer that something else uses this function or variable.
-+ */
-+#define __visible __attribute__((externally_visible))
-+
-+/*
-+ * GCC 'asm goto' miscompiles certain code sequences:
-+ *
-+ *   http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
-+ *
-+ * Work it around via a compiler barrier quirk suggested by Jakub Jelinek.
-+ *
-+ * (asm goto is automatically volatile - the naming reflects this.)
-+ */
-+#define asm_volatile_goto(x...)	do { asm goto(x); asm (""); } while (0)
-+
-+#ifdef CONFIG_ARCH_USE_BUILTIN_BSWAP
-+#define __HAVE_BUILTIN_BSWAP32__
-+#define __HAVE_BUILTIN_BSWAP64__
-+#define __HAVE_BUILTIN_BSWAP16__
-+#endif /* CONFIG_ARCH_USE_BUILTIN_BSWAP */
-+
-+#define KASAN_ABI_VERSION 4
--- 
-2.1.4
-
diff --git a/libre-testing/uboot4extlinux-omap3_beagle/PKGBUILD b/libre-testing/uboot4extlinux-omap3_beagle/PKGBUILD
deleted file mode 100644
index 9019ef4f7..000000000
--- a/libre-testing/uboot4extlinux-omap3_beagle/PKGBUILD
+++ /dev/null
@@ -1,48 +0,0 @@
-# U-Boot: BeagleBoard and BeagleBoard-xM
-# Maintainer: Isaac David <isacdaavid@at@isacdaavid@dot@info>
-# Contributor: André Silva <emulatorman@hyperbola.info>
-
-pkgname=uboot4extlinux-omap3_beagle
-pkgver=2016.01
-pkgrel=4.1
-pkgdesc="U-Boot with Extlinux support for BeagleBoard and BeagleBoard-xM"
-arch=('armv7h')
-url="http://git.denx.de/u-boot.git/"
-license=('GPL')
-conflicts=('uboot-omap3_beagle' 'uboot4grub-omap3_beagle')
-makedepends=('bc')
-backup=(boot/extlinux/extlinux.conf)
-install=${pkgname}.install
-source=("ftp://ftp.denx.de/pub/u-boot/u-boot-${pkgver}.tar.bz2"
-        '0001-parabola-arm-modifications.patch'
-        '0002-kernel-add-support-for-gcc-7.patch'
-        'extlinux.conf'
-        'uEnv.txt')
-sha256sums=('e5792fba9399d9804aa2ef667f14ff771e2cdece72367d340250265bf095a5d5'
-            'cf6519bab4270bf093eb6ff0d9f3b4d314d00af6c4ecad07c492977ae5c7f510'
-            '9e80aa27cccdb07b03d56a970f247c91d586d0b936868c076c20acc2e68a3968'
-            'bb489334db2d44562caa18ed6297068cf7df3afdf1bb8b1b1f27bce0d2b8e987'
-            'e3b0c44298fc1c149afbf4c8996fb92427ae41e4649b934ca495991b7852b855')
-
-prepare() {
-  cd u-boot-${pkgver}
-  patch -Np1 -i ../0001-parabola-arm-modifications.patch
-  patch -Np1 -i ../0002-kernel-add-support-for-gcc-7.patch
-}
-
-build() {
-  cd u-boot-${pkgver}
-
-  unset LDFLAGS CFLAGS CXXFLAGS
-
-  make distclean
-  make omap3_beagle_config
-  make
-}
-
-package() {
-  cd u-boot-${pkgver}
-  mkdir -p "${pkgdir}"/boot/extlinux
-  cp MLO u-boot.img "${srcdir}"/uEnv.txt "${pkgdir}"/boot
-  cp "${srcdir}"/extlinux.conf "${pkgdir}"/boot/extlinux
-}
diff --git a/libre-testing/uboot4extlinux-omap3_beagle/extlinux.conf b/libre-testing/uboot4extlinux-omap3_beagle/extlinux.conf
deleted file mode 100644
index bb48ab97f..000000000
--- a/libre-testing/uboot4extlinux-omap3_beagle/extlinux.conf
+++ /dev/null
@@ -1,43 +0,0 @@
-menu title Welcome to U-Boot with Extlinux support!
-
-timeout 50
-
-label Parabola GNU/Linux-libre, linux-libre kernel
-	kernel /boot/vmlinuz-linux-libre
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre
-
-label Parabola GNU/Linux-libre, linux-libre-lts kernel
-	kernel /boot/vmlinuz-linux-libre-lts
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-lts
-
-label Parabola GNU/Linux-libre, linux-libre-lts-knock kernel
-	kernel /boot/vmlinuz-linux-libre-lts-knock
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-lts-knock
-
-label Parabola GNU/Linux-libre, linux-libre-hardened kernel
-	kernel /boot/vmlinuz-linux-libre-hardened
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-hardened
-
-label Parabola GNU/Linux-libre, linux-libre-lts-apparmor kernel
-	kernel /boot/vmlinuz-linux-libre-lts-apparmor
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-lts-apparmor
-
-label Parabola GNU/Linux-libre, linux-libre-pck kernel
-	kernel /boot/vmlinuz-linux-libre-pck
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-pck
-
-label Parabola GNU/Linux-libre, linux-libre-rt kernel
-	kernel /boot/vmlinuz-linux-libre-rt
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-rt
-
-label Parabola GNU/Linux-libre, linux-libre-xtreme kernel
-	kernel /boot/vmlinuz-linux-libre-xtreme
-	append root=/dev/mmcblk0p1 rw console=ttyO2,115200n8
-	fdtdir /boot/dtbs/linux-libre-xtreme
diff --git a/libre-testing/uboot4extlinux-omap3_beagle/uEnv.txt b/libre-testing/uboot4extlinux-omap3_beagle/uEnv.txt
deleted file mode 100644
index e69de29bb..000000000
--- a/libre-testing/uboot4extlinux-omap3_beagle/uEnv.txt
+++ /dev/null
diff --git a/libre-testing/uboot4extlinux-omap3_beagle/uboot4extlinux-omap3_beagle.install b/libre-testing/uboot4extlinux-omap3_beagle/uboot4extlinux-omap3_beagle.install
deleted file mode 100644
index ed1fce75f..000000000
--- a/libre-testing/uboot4extlinux-omap3_beagle/uboot4extlinux-omap3_beagle.install
+++ /dev/null
@@ -1,11 +0,0 @@
-extlinux_warning() {
-  echo "==> WARNING: Remember to set up your kernels in /boot/extlinux/extlinux.conf"
-}
-
-post_install() {
-  extlinux_warning
-}
-
-post_upgrade() {
-  extlinux_warning
-}